With the Timbren kits you still have to abide by the overall capacity of the vehicle. Basically the Timbrens give you more suspension support to allow you to carry the capacity of the truck in the safest way possible but they do not allow you to increase the capacity of the truck.
Based on your truck's year/make/model and the numbers you found on your spring you do have the part # TGMRK10 which can give the truck up to 3,000 lbs of additional suspension support. If you need to replace... view full answer...
The overall height of the SumoSprings Solo Custom Helper Springs - Rear Axle # SSR-610-40 is 6 inches. These springs have a weight capacity of 1,000 lbs at 50-percent compression and are made of a durable mircrocellular urethane. They install in place of the factory bump stops.
I have attached a review and installation video for your reference. view full answer...
The Curt Front Mount Trailer Receiver, item # 31042, is designed to fit the 1997 Chevy K3500 4wd model vehicle that is not a factory cab and chassis design. The 34 inch measurement is taken from the outside of the frame to the outside of the frame.
The easiest way to determine if the Curt Front Hitch for the 1997 Chevrolet C/K Series 4wd Pickup, item # 31042, is to measure the bolt mounting holes across the frame, center to center. This measurement is 30-1/2 inches for this front mount... view full answer...
My technical contact at Brophy confirmed for me that the distance from the outer edge of the bracket to the welded-on V-shaped pieces is 2-3/4-inches. The edge of the weld is slightly closer to the outside of the bracket, approximately 2-1/2-inches. view full answer...
Sounds like you are trying to figure out the weight capacity for your 3 axle trailer. It is nearly impossible to determine leaf spring capacity based on dimensions. But you can determine axle capacity by measuring.
Since your axles are 3 inches in diameter it would seem that they are 6k to 7.2k rated axles.
For suspension enhancement to help support your current setup you would want the Timbren Trailer Suspension Enhancement # TTRA1032 or you would need to replace your current springs... view full answer...
The Westin Fey Diamondstep Rear Bumper # 20008 is approximately 72-3/8" in length and the Westin Fey Diamondstep Rear Bumper # 21000 is approximately 74-5/8" in length. view full answer...
The Square 2-Speed Jack w/ Crank # TJD2SP-12000SP-F has a high gear ratio which is 6.43 handle revolutions per inch of travel, and the low gear ratio which is 22.86 handle revolutions per inch of travel. view full answer...
The actual outside dimensions of the stake pocket anchors part # T55Z that you referenced where it slides into the stake pocket is the exact dimensions you listed. 3-1/2 inch by 1-1/2 inch. I attached a picture that has these dimensions listed. view full answer...
The B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25122 that will fit your 1986 Chevy K20 will measure 5.438" from the top of the frame brackets to the top of the receiver. If this is looking like it will not be enough to clear the bottom of your bumper, the # BWHDRH25198 may be the better option. This will measure 7.906" when also measured from the top of the frame brackets to the top of the receiver. Both of these American made Class V hitches will have the same 2" receiver opening as... view full answer...
The head alone for the B&W Companion hitch # BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds. view full answer...
Yes, check out the picture I attached that has the vertical distances from where the hitch mounts to the frame of the vehicle down to the hitch tube.
Since you need at least 6 inches this would clear that by 1-3/8 inches. view full answer...
Yes it will. I checked with Buyers Products and the Hitch Plate with Receiver Tube item # 3371809065 will fit a 1996 Chevy or GMC 3500HD so long as it is a cab and chassis model. view full answer...
The 1998 Chevrolet C/K Series Pickup Westin Signature Series Round Nerf Bars - 3" - Black Powder Coated Steel, # 25-0890, are a confirmed fit for your 1998 Chevrolet K1500 Extended Cab. They do have 4 step pads, 2 on each side, not the one on driver's side and two on passenger side you asked about. These are really nice bars with a chrome plated steel construction.
We don't have any nerf bars with the offset number of step pads compatible with your vehicle. Something like the 1998... view full answer...
I went out to the warehouse and took some measurements for the Curt Trailer Hitch Receiver item # 13028 you referenced. The measurement running from the middle of the bolt holes across the length of the receiver is 31-1/8". I can confirm that this hitch does fit a 1978 Chevrolet C/K Series Pickup. I have attached pictures of the measurements. view full answer...
The Shackle Links, # 115052, are 3/16 inches thick.
They are also 1-1/4 inches wide; 2-5/8 inches from the center of one hole to the center of the other hole, with a bolt hole diameter of 9/16 inches. view full answer...
The Erickson Truck Bed Ladder Rack w/ Load Stops - Aluminum - 800 lbs # EM07705 has crossbars that are 3-1/4 inches at the base and have a V shape. The height is 1-1/2 inches. This will be compatible with most Yakima kayak carriers like # Y04073 as well as the Thule Portage Canoe Carrier w/ Tie-Downs - Gunwale Brackets - Side Loading # TH819. view full answer...
Aries doesn't have the length of these bars listed out but if you look under your truck you'll see where the Aries Round Nerf Bars # AA204037-2 will mount (see attached instructions). Since the ends of the bars connect directly to the mounting brackets you'll be able to see exactly where these bars will end on your 1985 Chevy pickup. view full answer...
The measurement that you will want to take is the outer diameter of the inner ring and the outer diameter of the inner ring with one of the tabs (see photo). You will also want to count the bolt holes on the wheel and know the wheel diameter.
The Baby Moon Center Cap, # AM90086, will fit 13 inch, 14 inch, or 15 inch 5-lug conventional steel wheels. The outer diameter of the inner ring should be 9 inches and the outer diameter of the inner ring with one of the tabs should be 9-1/4 inches.... view full answer...
If you are absolutely sure you have a good 12 volt source ran to the black wire of the P2 part # 90885 and a good ground ran to the white wire of the controller and you are not getting any activity on the display of the controller it would be bad.
The display should at least light up. If not then the controller has an internal problem that needs to be addressed. view full answer...